Clipper C1320SS Manual do Proprietário

OWNERS MANUAL MEDIUM CONCRETE SAWS MODEL: C1320P FORM C1320P rev 9-2010

104. Inspect the blade for any damage, cracks, burnt or blue areas, missing segments, and roundness of blade. Also inspect the arbor hole and drive

117. Tighten the blade shaft nut (counter-clockwise for the Operator’s Right Hand side and clockwise for the Operator’s Left hand side). 8. Insure

12B. Changing the Blade Side: 1. Insure that the Ignition Power Key Switch is in the OFF position and then disconnect the spark plug. 2. Remove th

136. Remove the Blade Shaft Guard by removing the Blade Shaft Guard retaining bolts. See Blade Shaft Guard Removal diagram below. Blade Shaft Guar

1412. Remove the Pointer and reattach it to the Operators Left hand side of the machine. NOTE: Reverse the orientation of the Pointer 13. Reconnec

15 Before starting, insure that the blade is properly installed, all guards are in place and in safe operating condition, and that the Blade is not

16 Pull the starter grip lightly until you feel resistance, then pull briskly. CAUTION: Do not allow the starter grip to snap back against the engine

17F. Controls RaiseLevantarRPM/Hours (RPM/Horas)Lower Bajar3600 RPMIgnitionIgnicion Emergency Stop Paro deEmergencia Blade DiaEng rpmEng Pull

18Tachometer/Hour Meter: The Tachometer/Hour Meter shows the engine RPM only when the Engine is running. The total Engine operating hours (run time)

1911. Slowly lower the blade by rotating the hand wheel clockwise until the desired depth of cut is reached. Use a reasonable rate of feed. A reaso

2WARRANTY Norton warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of

20Additional Guide Lines For Sawing:  Understand and follow all of the instructions in this owner’s manual.  If wet cutting, turn on the water

21III. MAINTENANCE A. Engine Maintenance Follow the below schedule for engine maintenance. NOTE: Check the Honda Engine manual that came with the

22 Always refer to the engine manual for more detailed information on checking the oil, changing oil, and oil capacity, air filter changes, and fuel

23HONDA TECHNICAL & CONSUMER INFORMATION Warranty Service Information Servicing dealership personal are trained professionals. They should be

24B. Bearings Re lubrication type bearings must be relubricated daily to assure long life. The grease used should conform to the NLGI grade two con

25C. V-Belts Warning: Never make adjustments to belts or pulleys while engine is running! 1. The best tension for a belt drive is the lowest tens

26Main Causes of Belt Failures: Premature Belt failure can be attributed to the following issues: Tension (too much or too little), Pulley Misalignm

27The bearing used to support the raising screw should be checked after each use to make sure it is turning freely and lubricated. If the bearing re

28E. ELECTRICAL DIAGRAM C1320P: 13HP Manual Start Models Only Oil Alert Unit(BL)Transistorized Ignition Unit(BL)Oil LevelSwitch(Y)(G)Spark PlugKill S

29IV. PARTS LIST SECTION A. Ordering Information 1. List model number and serial number of machine. 2. List part number and serial number of part n

3Table of Contents CONTENTS PAGEWarranty Information 2I. Preparation A. Safety Precautions 4-6B. Assembly 7C. Concrete Saw Specifications 8II. Ope

30 3455429543294551130543511305435433453589781311126262535543345227115141017 C1320P Frame Group

31 C1320P Frame Group Item Part No UPC No Description QTY Type NOTES 1 238171 70184628065 LIFT FRAME 1 S 2 238175 70184628066 LIFT FRAME HOOK

32 82474441091112132151244411353661414 C1320P Raise Axle Group

33 C1320P Raise Axle Group Item Part No UPC No Description QTY Type NOTES 1 238134 70184628082 RAISE AXLE MOUNT 1 S Sold as Each. 2 238129 7

34 1234456789108910111213141517211218191819192023 C1320P Blade Shaft & Engine Group

35 C1320P Blade Shaft & Engine Group Item Part No UPC No Description QTY Type NOTES 1 238179 70184628084 BLADE SHAFT 1 S 2 227159 70184673

36 11051413161514137161519 C1320P Blade Guard and Water System Group

37 C1320P Blade Guard and Water System Group Item Part No UPC No Description QTY Type NOTES 1 N1D0082 70184659115 HOSE SWIVEL 1 S 2 N1C0021 7

38 1267910115438128 C1320P Controls and Console Group

39 C1320P Controls and Console Group Item Part No UPC No Description QTY Type NOTES 1 238120 70184627887 HANDLE BAR 1 S 2 N1C0004 70184659110

4I. PREPARATION A. Safety Precautions Important! The following safety precautions must always be observed. Hazard Symbols Fuel (gasoline) is ex

40 12345678910111213141516171819202119211922 C1320P Depth Adjustment Group

41 C1320P Depth Adjustment Group Item Part No UPC No Description QTY Type NOTES 1 238164 70184628181 DEPTH SCREW TUBE 1 S 2 238234 70184628

42 1243495108To Blade Guard7 C1320P Optional Water Tank Group

43 C1320P Optional Water Tank Group Item Part No UPC No Description QTY Type NOTES -NA- 238001 70184628014 WATER TANK KIT 1 S INCLUDES: Items

44 Saint-Gobain Abrasives 2770 West Washington Stephenville, TX 76401 Phone: 254-918-2310 Fax: 254-918-2312

5 Dust and Silica Warning Grinding/cutting/drilling of masonry, concrete, metal and other materials can generate dust, mists and fumes containing c

6 1. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling or previo

7I. PREPARATION B. Assembly The C1320P push concrete saws are shipped completely assembled and ready for use except for diamond blade, gasoline, oi

8C. C1320P Concrete Saw Specifications Dimensions/Weight C1320P Length (Transport) 56 inch (1142 mm) Width 26 inch (660 mm) Height 40 inch (1016 mm)

9II. OPERATION Read and understand this manual before running or using the machine! A. Installing the Blade 1. Insure that the Ignition Power Key